Exactly How To Install A Bath Tub (For Novices).
Schedule A ServiceWe've found this article involving Installing A Bathtub listed below on the web and felt it made perfect sense to discuss it with you on this site.
Setting up a bathtub isn't exactly brain surgery, however it does require strong plumbing, woodworking, as well as in some cases, tiling abilities. Replacing an old bathtub with a brand-new one is likewise a moderately hard task. If the old tub is readily easily accessible, the job can move easily; if you need to open up a wall surface to eliminate the old tub as well as position the new bathtub, the job is a lot harder. In either instance, the task is within a house handyman's abilities, although you will require an assistant to move out the old bathtub and also set in the new one. See to it you have actually qualified yourself for the work as well as are comfortable trying it. As opposed to hiring a service provider to take over a halfway-completed task, it is far better to think about using one prior to you begin. Opportunities are you may require an expert plumber to make tube connections.
This write-up will aid you set up a new bath tub in your restroom if you have actually already bought a brand-new tub and also do not need to alter the arrangement of your previous water pipes.
Your devices as well as product checklist should make up the following:
Getting ready for the Installment
Firstly, the sustaining frame provided with the bath ought to be fitted (if called for) according to the producer's guidelines. Next, fit the faucets or mixer to the bathtub. When suitable the tap block, it is very important to make sure that if the tap features a plastic washer, it is fitted between the bathroom and the faucets. On a plastic bath, it is additionally sensible to fit a sustaining plate under the taps device to avoid pressure on the tub.
Fit the adaptable tap adapters to the bottom of the two taps making use of 2 nuts and olives (often provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet through the hole in the bath. Make use of the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Ensure you utilize every one of the provided washing machines.
Attach the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom must currently prepare to be suited its last placement.
Removing Old Touches
If you need to replace old taps with new ones as a part of your installation, then the first thing you should do is disconnect the supply of water. After doing so, switch on the taps to drain any water staying in the system. The process of eliminating the existing taps can be quite problematic due to the limited accessibility that is usually the situation.
Utilize a container wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipelines to the faucets. Have a fabric all set for the continuing to be water that will certainly originate from the pipelines. When the supply pipes have been removed, use the very same device to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the single faucets from transforming throughout this process. Once the taps have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any old sealing substance.
Prior to carrying on to fit the brand-new taps, compare the pipe connections on the old taps to the brand-new faucets. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the new taps to fit.
Mounting the Bath tub
Making use of both wooden boards under its feet, put the bathtub in the required position. The wood boards are practical in equally spreading out the weight of the tub over the area of the boards instead of concentrating all the weight onto 4 little points.
The next objective is to make certain that the tub is leveled all round. This can be accomplished by checking the spirit level as well as changing the feet on the bathtub until the spirit level reads degree.
To mount faucets, fit all-time low of the furthest versatile tap connector to the appropriate supply pipeline by making a compression sign up with; after that do the exact same for the other tap.
Switch on the water supply and also examine all joints as well as new pipework for leaks and tighten them if essential. Load the tub and also examine the overflow electrical outlet as well as the typical outlet for leakages.
Ultimately, take care of the bath paneling as described in the supplier's instruction manual. Tiling and also securing around the tub should wait till the bath tub has been used at the very least when as this will resolve it right into its final setting.
Fitting New Touches
If the tails of the brand-new taps are plastic, after that you will certainly need a plastic connector to stop damage to the thread. One end of the adapter fits on the plastic tail of the tap and the various other end offers a connection to the current supply pipes.
If you require to fit a monobloc, after that you will certainly need decreasing couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next, place the tap in the mounting opening in the bath/basin guaranteeing that the washing machines are in area between the faucet as well as the sink. Safeguard the tap in position with the manufacturer given backnut. Once the faucet is safely in position, the supply pipes can be attached to the tails of the taps. The taps can either be linked by using corrugated copper piping or with typical tap ports. The former kind should be linked to the tap finishes initially, tightening just by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bathtub
In the area where the bathroom fulfills the tile, it is required to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can move enough to split a stiff seal, creating the water to pass through the wall surface between the bath and also the tiling, resulting in issues with dampness as well as feasible leakages to the ceiling below.
You can select from a selection of coloured sealants to assimilate your components and installations. They are marketed in tubes and cartridges, as well as can securing gaps as much as a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with spins of soaked newspaper or soft rope. Keep in mind to constantly fill the bathtub with water before securing, to permit the movement experienced when the tub is in usage. The sealer can fracture fairly early if you do not take into consideration this activity prior to sealing.
Alternatively, ceramic coving or quadrant tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also quickly available on the market. It is recommended to fit the ceramic tiles utilizing waterproof or water-proof sticky and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I discovered that piece of writing on Installing A Bathtub while doing a lookup on the search engines. Do you know about someone else who is fascinated about the niche? Please feel free to share it. Thanks so much for taking the time to read it.
Appointment